ASTM A/AM: Standard Specification for Steel, Strip, Carbon ( Maximum Percent), Cold-Rolled. ASTM A Standard Specification for Steel, Strip, Carbon ( Maximum Percent), Cold-Rolled1_幼儿读物_幼儿教育_教育专区。. ASTM A Carbon Steel, Tempers 4 or 5, Composition Spec. Categories: Metal; Ferrous Metal; ASTM Steel. Material Notes: Cold Rolled Strip. Vendors: No.
|Published (Last):||20 May 2004|
|PDF File Size:||4.96 Mb|
|ePub File Size:||14.6 Mb|
|Price:||Free* [*Free Regsitration Required]|
However, unless the order species the applicable “M” specication designation SI unitsthe material shall be furnished to inch-pound units.
ASTM A Carbon Steel, Tempers 4 or 5, Composition Spec
Link to Active This link will always route to the current Active version of the standard. The production of this nish requires extreme care in processing and extensive inspection. A Over 12 34 Specied Thickness, in. These elements are considered as incidental and are not normally determined or reported. Proper identication of parts may asstm visual examination, prints or descriptions, or a combination of these. The values stated in each system are not exact equivalents; therefore, each system aastm be used independently of the other.
All tests and inspection except product analysis shall be made at the place of manufacture unless otherwise agreed. Specied thickness must be within ranges stated for specied width. B The analysis shall be reported. See applicable gure in Test Methods and Denitions A The values listed are not exact conversions of the values listed in the inch-pound atsm, but instead are rounded or rationalized values.
It is recommended that hardness numbers be specied to the same scale as that to be used during testing.
Questions or comments about MatWeb? Please contact us at webmaster matweb.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn. Rejection and Rehearing A medium soft cold-rolled strip intended for limited bending, shallow drawing and stamping. Data sheets for overmetals, plastics, ceramics, and composites.
A soft ductile cold-rolled strip intended for deep drawing where no surface strain or 1a09 is permissible. The contents, results, and technical data from this site may not be reproduced either electronically, photographically or substantively without permission from MatWeb, LLC. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
Users requiring more precise data for scientific or engineering calculations can click on the property value to see the original value as well as raw conversions to equivalent units. Please click here if you are a supplier and would like information on how to add your listing to this material. However, the document shall clearly identify the organization submitting the document.
Click here to view all the property atsm for this datasheet as they were originally entered into MatWeb. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
ASTM A109 Grade 1 hard
The producer shall be notied as soon as possible so that an investigation may be initiated. Historical Version s – view previous versions of standard. This table is presented as a matter of general information. Over 12 to Over However, some applications are specied as silicon killed.
For most end part application only one kind of mechanical test requirement is normally employed. The phenomenon of aging is accompanied by a loss of ductility with an increase in hardness, yield point, and tensile strength.
Rockwell Hardness Maximum approx. Zstm if you don’t have an account with us yet, then click here to register. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values.
When the above aging characteristics are undesirable, special killed generally aluminum killed steel is used.
Packaging and Package Marking Login to see your most recently viewed materials here. Workmanship, Finish, and Appearance Notwithstanding the absence of a signature, the organization submitting the document is responsible for the content of the document.
The term weight is used when inch-pound units are the standard. Temper and Bend Test Requirement 7. Last previous edition A —