ASTM D149-97A PDF

Buy ASTM Da() Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at. Dielectric Strength ASTM D, IEC Scope: Dielectric Strength is a measure of the electrical strength of a material as an insulator. Dielectric strength is. ASTM DA – Designation: D – 97a (Reapproved ) An American National Standard Standa.

Author: Karr Faegami
Country: Bulgaria
Language: English (Spanish)
Genre: Environment
Published (Last): 21 May 2010
Pages: 153
PDF File Size: 18.7 Mb
ePub File Size: 3.12 Mb
ISBN: 861-8-47899-789-3
Downloads: 13462
Price: Free* [*Free Regsitration Required]
Uploader: Doushakar

These processes may continue until a complete failure path is formed between the electrodes. Summary of Test Method 4. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

For this reason it is important that the electrodes to be used be described when specifying this test method, and that they be described in the report.

The material of the gaskets or seals around the electrodes d1499-97a the potential to in?

The dielectric breakdown voltage test represents a convenient preliminary test to determine whether a material merits further consideration, but it falls short of a complete evaluation in two important respects. Breakdown is when an electrical burn-through punctures the sample, or decomposition occurs in the specimen.

The dielectric breakdown voltage test represents a convenient preliminary test to determine whether a material merits further consideration, but it falls short of a complete evaluation in two important respects. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

  KX-TA616 INSTALLATION MANUAL PDF

The power rating for most tests will vary from 0.

This standard does not purport to address all of the safety concerns, if any, associated with its use. Use the short-time test unless otherwise specied. Precision and Bias Within the limits speci? For such materials, the bath must be of such design that it will not be necessary to expose the aatm to air before testing.

Dielectric Strength ASTM D149, IEC 60243

These processes may continue until a complete failure path is formed between the electrodes. Also see Note 1.

Repeated applications of voltage will sometimes result in failure at lower voltages sometimes unmeasurably lowusually with additional damage at the breakdown area. Need help or have a question? D — 97a The power rating for most tests will vary from 0. The voltage is increased from zero or from a level well below the breakdown voltage, in one of three prescribed methods of voltage application, until dielectric failure of the test specimen occurs.

A number of different physical arrangements of voltage source, measuring equipment, baths or ovens, and electrodes are possible, but it is essential that 1 all gates or doors providing access to spaces in which there are electrically energized parts be interlocked to shut off the voltage source when opened; 2 clearances are sufficiently large that the eld in the area of the electrodes and specimen are not distorted and that ashovers and partial discharges corona do not occur except between the test electrodes; and 3 insertion and replacement of specimens between tests be as simple and convenient as possible.

Other electrodes may be used as specied in ASTM standards or as agreed upon between seller and purchaser where none of these electrodes in the table is suitable for proper evaluation of the material being tested.

  HORHE LUIS BORHES KRATKE PRICE PDF

ASTM D 97a The exposure limits are set by governmental agencies and are usually based upon recommendations made by the American Conference of Governmental Industrial Hygienists. If the items listed in 5.

Calibrate the currentsensing dial in terms of specimen current. C The electrodes surfaces should be polished and free from irregularities resulting from previous testing. The electrode area may have a signicant effect upon what the current setting should be. If failure occurred while the voltage was being increased to the starting voltage the failure time shall be zero. This will usually reduce the probability of surface ashover. D-7, Glenway Ave.

Dielectric Strength ASTM D, IEC

The voltage is increased from zero or from a level well below the d419-97a voltage, in one of three prescribed methods of voltage application, until dielectric failure of the test specimen occurs. If a test set with motor-driven voltage control is available, the slow rate-of-rise test is simpler and preferable to the step-bystep test.

With solid materials the discharges usually occur in the surrounding medium, thus increasing the test area and producing failure at or beyond the electrode edge. Generally speaking, the effect of the d149-97x material is difficult to establish because of the scatter of experimental data.