FBI XL2T PROGRAM PDF

Introduction The XL-2T is a state of the art microprocessor-based control/ communicator. The system features seven (7) fully programmable zones. Programming. XL-2T. Security System. Installation and Setup Guide. STAY. INSTANT. ACYLB. READY APPENDIX D – SYSTEM PROGRAMMING WORKSHEET. Example: To program phone number enter 1#8#0#0# etc. Exit Program STAY. Default Panel Short “EEPROM RESET” pins on panel and power up system.

Author: Maugore Taulkis
Country: Philippines
Language: English (Spanish)
Genre: Software
Published (Last): 6 January 2008
Pages: 372
PDF File Size: 12.47 Mb
ePub File Size: 10.33 Mb
ISBN: 369-3-74783-355-3
Downloads: 48748
Price: Free* [*Free Regsitration Required]
Uploader: Tamuro

The keypad will indicate a trouble on the fire zone if the bell or sounder is not properly connected.

Replacement microprocessors are available through Technical Support or Customer Service. We regret any inconvenience this may bfi caused and appreciate your continued support of FBII products.

FBII XL-2T Installation And Setup Manual

The purpose of this manual is to give you a brief overview of the XL-2T control panel, and provide instructions for installing a basic system. A-2 Partial Extended 3×1 Part. A-2 3×2 or 4x Some new features have been added and others have been modified. The following is a quick comparison. Sounder Only always enabled Programmable Dialer Attempts: The system features seven 7 fully programmable zones. Programming can be performed through any of the compatible keypads or the system can be uploaded and downloaded remotely using the EZ-Mate PC Downloader Software.

The door of the metal cabinet may be removed to make it easier to install the control panel. Create an opening and mount a standard double-gang box. Secure keypad to double-gang box as shown in graphic at left. The double-gang box shall be mounted flush with wall in order for keypad screws to fit. Directly to a control panel having a keypad cutout on the front of its enclosure. Directly to a single or double gang electrical junction box.

The keypads can be surface mounted or flush mounted as described below. The keypads are surface mounted as described below. Separate the two halves of the keypad by placing a straight-slot screwdriver into one of the two slots at the bottom of the keypad and twisting. Select the desired location between wall studs for mounting the keypad. The rear plastic mounting plate is not used for recessed installations. For UL installations see wiring diagram for hookup.

Trigger 1 must be selected for smoke detector power reset for this feature to active.

FBII XL-2T INSTALLATION AND SETUP MANUAL Pdf Download.

Fire Trouble is reported to the CS if enabled program question 32, location 3. If the siren xl2g already sounding, the supervision will not take effect until after bell cutoff time.

See the following diagram: Refer to the Installation Instructions for hookup information.

  HISTORIA DE LA FILOSOFIA FREDERICK COPLESTON TOMO III PDF

With this device some systems can obtain dial tone in areas which do not automatically provide dial tone. At the moment telephone line seizure occurs, the Telco Tip is momentary connected to earth ground to access dial tone. Each condition will cause these LEDs to operate differently as follows: System ready to be armed System not ready to be armed Section 5 – System Operations Keypad Sounder The sounder or loudspeaker housed inside the keypad, emits annunciates sounds according to the condition of the security system.

The keypad sounder annunciates differently to indicate the following conditions: When the switch is pushed toward the front of the keypad, in the opposite direction of the arrowthe switch is in the OFF position.

LCD display keypads will indicate the following message: The system contains up to fifteen user codes 4 digits each with the xo2t applications: Section 5 – System Operations User Deletion User codes can be deleted directly through the keypad. Once deleted their values will be null. Quick Arming allows arming the system without entry of a user code and will report as user The system must be in ready mode.

A user code is required to disarm the system. Section 5 – System Operations If a user code is not required to set the time, then enter: On LED keypads the sounder will beep after each entry. The auto arm time represents the time of day that the area will automatically arm if it is not already armed. If selected, then a negative acknowledgment 4 short beeps will be heard after attempting to enter this mode. Upon entry to the system log view, LCD based keypads will show the events one at a time starting from the oldest event.

Section 5 – System Operations 4. Proceed to question 02 through the sequence Ffbi, enter the desired account number each digit followed by the fbo. This will be used by the CS downloading computer to determine the proper account information to download to this subscriber.

Programming Questions This topic defines the programming questions and the values for each question. The system will report all signals to the primary receiver phone number.

The checkmark highlights which options are selected. Question 10, L1 – Burglary Bell Time-out Question 11, L1 – Exit Delay For Built-in Siren Driver, connect a progfam 8 ohm speaker only. For Bell Output, connect a siren driver ex: To select a trigger type enter the 2 digits in either L1 L2 or L3 L4 desired trigger type for each output trigger.

Enter the digit from the table below.

Upon detection of the first violation, smoke detector power on conventional 4 wire smoke detectors connected to ZONE modules will be reset for a period of 8 seconds. After this time period, power is restored. For a period of 5 seconds the fire zone will not be scanned allowing the smoke detectors to settle.

  ALESIS MULTIMIX 8 USB MANUAL PDF

The restore code will also be reported if the system is disarmed during an alarm. This enables Fire and Burg zones to report restores. Question 32, L1 fb Bypass Code If a keypad tamper code is entered then it will be transmitted to the Central Station. Section 6 – System Programming When programming the English zone descriptors, use the following techniques to program the characters: There are 36 total questions, with multiple data entry locations. The Extended Reporting Format: The FCC requires the following statement for your information.

This equipment generates and uses radio frequency energy and if not installed and used properly, that is in strict accordance with the manufacturer’s instructions may cause interference to radio and television reception. Page of 93 Go.

Page 81 – Extended 3×1 Ext. Table of Contents Add to my manuals Add.

Page 23 Fire Trouble is reported to the CS if enabled program question 32, location 3. Keypad Sounder Section 5 – System Operations Keypad Sounder The sounder or loudspeaker housed inside the keypad, emits annunciates sounds according to the condition of the security system.

Page 40 Section 5 – System Operations If a user code is not required to set the time, proogram enter: System Programming Programming Questions This topic defines the programming questions and the values for each question. Page 70 Section 6 – System Programming When programming the English zone descriptors, use the following techniques to program the characters: Comments to this Manuals Your Name.

Enter text from picture: Good Day I had a four digit user code, but the last digit was lost. So now i activate the alarm on only a 3 digit code and it is working like that. I want to change this 3 digit code to a new 4 digit code, but with no success. I pressed the code button ready light did not xo2tthen pressed both 7 and 9 at same time, to reset master code to The alarm was then activated, without me activating it.

I then pressed code button followed by master codethen user no 3 and then new 4 digit user code. How can i change or get rid of this 3 digit code. It is xl2r to change code for security reasons. I shall be pleased to learn from you in this regard. By pressing ‘print’ button you will print only current page. To print the manual completely, please, download it.

Don’t show me this message again. Got it, continue to print. Don’t have an account?