HT12D DATASHEET IN PDF

HT12D 2 12 Series of Decoders Features. Operating voltage: V~12V Low power and high noise immunity CMOS Built-in oscillator needs only 5% resistor. IC HT12D can be used only with its pair HT12E. These two ICs together form an Encoder and Decoder pair. They are bit. HT12D Datasheet, HT12D Holtek Decoder Datasheet, buy HT12D Decoder IC.

Author: Kigasida Yobei
Country: Belgium
Language: English (Spanish)
Genre: Finance
Published (Last): 2 August 2010
Pages: 67
PDF File Size: 5.59 Mb
ePub File Size: 16.23 Mb
ISBN: 742-5-70400-463-9
Downloads: 83304
Price: Free* [*Free Regsitration Required]
Uploader: Kajisar

This pin will go high when a hht12d is received. The input data code is decoded when no error or unmatched codes are found. SPI Module of Arduino.

So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. This series of decoders are mainly used for remote control system applications, like burglar alarm, car door controller, security system etc. Interface SD Card with Arduino. A basic circuit diagram for the HT12D IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

This oscillator can be used by connecting these two pins through a 1M Resistor.

HT12D/HT12F – Product Details – Holtek

A valid transmission in indicated by a high signal at VT pin. It is not mandatory to use it. These two ICs together form an Encoder and Decoder pair.

Connected to the Ground of circuit. Virgin Galactic — Commercial Space Flight.

  EL CHIBAK PDF

HT12D Decoder IC

Hf12d out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. The 4-bit data that is received can be obtained on pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7. The serial input data is compared with the local addresses three times continuously. Arduino based GPS receiver. For decoding a data the IC will requires an oscillatorluckily this IC has one in-built.

Valid transmission; active high. Supply voltage; 5V 2.

HT12D Decoder IC | HT12D Datasheet | Pin Diagram

It is very important that your Decoder should have the same address of that of the encoder. What is Web Browser.

We should set the bits in same pattern on Encoder and Decoder IC to pair them. HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits. This oscillator can be used by connecting these two pins through a 1M Resistor 17 Valid Transmission VT This pin will i high when a data is received.

Interface GPS with Arduino. To know how a 4-bit data can be encoded and then send to the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is given here. This high-density System-in-Package SiP integrates controller, power switches, and support components. These are the 8-bit address bits, which is used to protect your data.

This pin powers the IC should use only 5V. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.

  HAYATUS SAHABAH ARABIC PDF

They can also be connected to LED to physically view the received data. Skip to main content. In simple terms, HT12D converts the serial input into parallel outputs. If you want security you can connect any of the 8 pins to 5V to make it high. They are paired with 2 12 series of encoders. In i above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

The IC has a built in oscillator. Submitted by datasheeet on 27 October Choosing Motor For Robots. Choosing Battery for Robots. The data on 4 bit latch type output pins remain unchanged until new is received.

The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded. TL — Programmable Reference Voltage. HT12D is a decoder integrated circuit that belongs to 2 12 series of decoders.

If any valid data is received they can be obtained from these four pins. It decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to output data pins.

The Encoded 12 bit output data obtained from HT12E has to be given here. It is mainly provided to interface RF and infrared circuits.