The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to. à aiguille interne. STANDARD. ISO. Second edition. Reference number. ISO (E). Provläsningsexemplar / Preview. STANDARD. ISO. Second edition. Reference number. ISO (E). This is a free 4 page sample. Access the full version online.
|Published (Last):||1 December 2006|
|PDF File Size:||10.68 Mb|
|ePub File Size:||18.68 Mb|
|Price:||Free* [*Free Regsitration Required]|
An example of a suitable apparatus is shown in fig- ure B. Standards are also reviewed periodically; a standard alongwith amendments is reaffirmed when such review indicates that no changes are needed; if the review indicates that changes are needed, it is taken up for revision.
All standards are subject to revision, and parties to agreements based on this part of ISO are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. If a steel tube is used, it shall connply with ISO Add the following reference: For the purpose of deciding whether a isp requirement of this standard is complied with, the final value, observed or calculated expressing the result of a test or analysis, shall be rounded off in accordance with 10555-5 2: Part 1 General requirements do The technical committee has reviewed the provisions of the following International Standard referred in this adopted standard and has decided that it is acceptable for use in conjunction with this standard: At the time 1055-55 publication, the editions indicated were valid.
The corresponding Indian Standards which are to be substituted in their places are listed below along with their degree of equivalence for the editions indicated: Assembly comprising at least a needle tube attached to, and communicating with, a needle hub. Suggested colour references for opaque naaterials are given in annex C. Designation and catalogue of CCR colours.
No part of the these publications may be reproduced in any form sio the prior permission in writing of BIS.
The catheter tube may have a single lumen or multiple lumens. I Principle Water is allowed to flow through the catheter and the amount of flow is measured either volumetrically or gravimetrically.
EN ISO – European Standards
The details of conditions under which the licence for the use of the Standard Mark may be granted to manufacturers or producers may be obtained from the Bureau of Indian Standards. Fitting attached to the needle tube, providing communication with its bore.
Copyright BIS has the copyright of all its publications. Bureau of Iwo Standards BIS is a statutory institution established under the Bureau of Indian Standards Act, to promote harmonious development of the activities of standardization, marking and quality certification of goods and attending to connected matters in the country. Limited collection of colours.
Certain conventions are, however, not identical to those used in Indian Standards. Until that time, a manufacturer may label his product “radio- opaque” provided he can support this claim by demonstrat- ing that he has isl appropriate method for showing radio- opacity.
When tested in accordance with annex E, fluid shall not leak out of the vent fitting within 15 s.
CSN EN ISO 10555-5
Available from Munsell Color, N. The fluid is allowed to flow into the needle, and the time taken for fluid to leak through the vent fitting is measured. The number of significant places retained in the rounded off value should be the same as that of the specified value in this isoo.
Review of Indian Standards Amendments are issued to standards as the need arises on the basis of comments. Rigid tube with one 10555- sharpened to facilitate entry into body tissue.
An approved test method for producing a value of radio-detectability will be established. Users of Indian Standards should ascertain that isso are in possession of the latest amendments or edition by referring to the latest issue of ‘BIS Catalogue’ and ‘Standards: In this adopted standard, reference appears to certain International Standards for which Indian Standards also exist.
Fixed or removable fitting per- mitting venting of air while restricting or preferably preventing the escape of blood. Annex Kso shows examples of typical needle point geom- etries. Peripheral intravascular catheter designed for the introduction of withdrawal of liquids or devices into or from the peripheral vascular system. This does not preclude the free use, in the course of implementing the standard, of necessary details, such as symbols and sizes, type or grade designations.
This Indian Standard has been developed from Doc No.: Measure the time taken for fluid to form the first falling drop at the back of the vent fitting. International Standard ISO Attention is particularly drawn to the following: NOTE 3 The point should be designed to be noncoring. Blood flow into the needle hub. NOTE To improve the visibility of the solution, a colorant 10555–5 as red or blue food dye may 105555-5 incorporated.
Other parts of this standard are as follows: When the needle is fully inserted into the catheter unit, the catheter tube shall neither extend beyond the heel of the needle bevel nor be nnore than 1 nnnn fronn it see dinnension a in figure 1.