LM is an adjustable voltage regulator IC used for shunt regulator, current regulator, and temperature controller. The LM LMC is a voltage regulator designed primar- ily for series regulator applications By itself it will supply output currents up to mA but external. Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. 2All trademarks are the property of their respective.

Author: Tygorg Yozshukasa
Country: Kosovo
Language: English (Spanish)
Genre: Literature
Published (Last): 5 June 2004
Pages: 51
PDF File Size: 17.11 Mb
ePub File Size: 14.37 Mb
ISBN: 122-3-37444-831-5
Downloads: 82959
Price: Free* [*Free Regsitration Required]
Uploader: Kigul

If we pragmatically summarize the pros and cons of this methusalem, we end up with something like this:. Take all networks into account, and make sure that the reference divider and the output sampling network present the datasyeet impedance to the error amplifier inputs. The net and some manufacturers application notes are also a good source of information. They see this chip as an old-age part that has no merits today. Current limiting sensitive to overload.

National Semiconductor

First, ST went out of the LM business. The performance of an LM is not bad at all, especially for noise and long term stability. The way to go is dataheet high side sensing with an op amp that can do that, or a floating design like the famous Elektor one from 1 x LM, 2 x LM Naturally, it is frowned upon by a lot of designers that are just half as old.


If you need to regulate lower voltages, the LM chip itself needs a separate power datashert at 10V minimum. With less accurracy, you may go below that, but not by much. Both have been making s for decades, and after the sale TI took over the National Semiconductor designation of LM and used their own of uA You are commenting using your WordPress. They dont make this part anymore. You are commenting using your Twitter account.

LM Datasheet(PDF) – National Semiconductor (TI)

Some extra bleeders are needed to make falling edge output regulations fast enough. Support for external pass transistorskeeping on-chip dissipation and therefore drift low. Fill in your details below or click an icon to log in: After some ping-pong TI recommended the MIL-spec datahseet and guaranteed that this would be free from drift. The LM is not discontinued at all, sold by TI in the millions, available from all electronic distributors and dirt cheap. For your bread-and-butter PSU, they are still fine and noise is quite low.

Its comparing apples and oranges. Leave a Reply Cancel reply Enter your comment here I added a reference study that compares voltage regulator noise. It can able to provide a higher range of output voltage and current up to 10A by simply adding a series pass transistor with it, with having a wider range of operating temperature so the Dataasheet able to withstand for long.


This is due to the 7. The collector voltage Vc driving the output does not need to be stabilized.

Provide enough voltage headroom. This cancels the error amps base bias currents. Before you specify a compensation cap, run a few tests using SPICE to see if gain and phase margins are in order.

A Collection of Proper Design Practices using the LM723 IC Regulator

Minimum dropout voltage is ca. Tempco is also very good, also when compared to newer chips. LM lk723 an adjustable voltage regulator IC used for shunt regulator, current regulator, and temperature controller.

If you use current limiting, protect the base of the limiting transistor by a 1K, e. Input voltage goes up tp 40V constant, with 50V pulses allowed.

Pin configuration Pin No.

People used to 3-terminal regulators are in for a culture shock caused by the amount of design aspects to consider.

On a transistor level, you can satasheet some design tricks by the legendary Bob Widlar: No wonder after 50 years, it is known what you may expect and what not.

The LM values translate to about 0. Click here for lm7223 larger resolution picture … A lot of basic application circuits can be found in the LM datasheet.